SUPER CURTAIN ROBOT MOTOR INSTRUCTIONS (Model: ZM85EL-2x)

Below is the user manual for the ZM85EL super curtain robot motor, including basic information about the robot, installation steps, instructions for setting up the remote control, and instructions for networking the motor with the App (ZigBee, Bluetooth versions), etc.; Please feel free to check!

To begin, let’s take a brief look at the structure, main functions, and parameters of the Smart Curtain Robot.

Super Curtain Robot Motor

ELECTRONICS BUILT-IN RECEIVER

  • Super silent design
  • Power off and position memory function
  • Wireless control: RF remote, ZigBee, Bluetooth
  • Built-in lithium battery
  • Smart home connection
  • Percentage control position
  • Inching / continuation move mode
  • For multi type of the curtain: Rome rod, Straight track, Curved track

Technical Parameters

Product modelInput
voltage
PowerRPMTorqueRated
current
Battery capacity
ZM85EL-2xDC 5V8W30RPM0.5N.m500mA7.4VDC/3000mAh

Next, let’s get into the charging power supply and button manual for the smart curtain robot motor.

Charging Power Supply Instructions

⚠ LOW BATTERY: The motor will raise an alarm with a voice “Di” to warm low battery.
PIease charge the device then avoid over-discharge to damage motor or abnormal operation.
Full charge the device for 6 hours before first use.
Please charge the device for at least 6 hours every 3 months to prolong the battery life.

* When charging the motor, it is necessary to use the factory-configured charging cable to charge.

    Button Manual

    RJ11: Used for weak current control: Dry contact control, RS485 control, etc. Connect to the data center for controlling center by means of a data cable, which is a wired control.

    Accessories instruction



    Of course, in addition to the curtain robot, there are remote controls (optional), which have different functions for different models!

    Remote Control Instruction


    Then, here’s your main concern, which is how to install curtain robots on different curtain tracks!

    Installation Steps

    Rome rod installation steps

    The number of grids on both sides of the teeth of the adjustable ring (3-4 grids are recommended for 28mm diameter pipes; 4-5 grids are recommended for 25mm pipes; 6 grids are recommended for 20mm pipes)
    Push the ring with your thumb, put it into the curtain rod.

    It is recommended to hold the adjustable cover with your hand and use the palm of your hand.

      Disassembly steps

      Press the adjustable buckles on both sides at the same time.

      Special installation steps for square tracks/ curved tracks

      Use a small screw driver to push up the ear on the left to add a grid tooth.
      Use a small screw driver to push up the ear on the right to add a grid tooth.
      Gradually add a grid of teeth to the left and right, adjust the number of grids upward to a suitable position, and get the curtain robot in position.

      Curved track installation steps



      Tilt the motor to the left to increase the adjustable wheel teeth by one grid.
      Tilt the motor to the right to increase the adjustable wheel teeth by one grid.
      Gradually add a grid of teeth to the left and right, adjust the number of grids upward to a suitable position, and get the curtain robot in position.

      Small curtain track installation steps



      Tilt the motor to the left to increase the adjustment wheel teeth by one grid.
      Tilt the motor to the right to increase the adjustable wheel teeth by one grid.
      Gradually add a grid of teeth to the left and right, adjust the number of grids upward to a suitable position, and get the curtain robot in position.

      Big curtain track installation steps



      With the above step-by-step installation instructions combined with this detailed tutorial video, I’m sure you’ll be able to do it easily!

      Curtain Robot Installation Tutorial Video

      After a general understanding of ZM85EL smart curtain robots, you should be eager to know how to control them, right? Here’s how to control the curtain robots by remote control.

      Remote Control and Network Setting Manual

      These operations only work for the remote control within the effective control distance, and the motor is in the power-on state, otherwise it doesn’t work.

      Please finish this process within 5 seconds, otherwise it will exit the setting due to overtime.


      First, run the motor to the limit position you want to set and pause, then perform the following operations. If the motor has travel limit already, you need to clear the original travel before resetting it.

      Open and close limits must be set first, in order to using the percentage control function.


      Open limit setting

      Please finish this process within 5 seconds, otherwise it will exit the setting due to overtime.


      Close limit setting

      Please finish this process within 5 seconds, otherwise it will exit the setting due to overtime.


      Delete the remote current channel from motor


      Delete current remote from the motor

      To cancel the connection between the motor and current remote all channels.


      Delete all remote from the motor

      To cancel the connection between the motor and all remote controls.

      Long press the motor’s “Set key” until the motor makes a sound “Di”, the motor light flashes rapidly,

      The following functions can be set as personal needs.

      Change the remote control direction

      Repeat this operation for “Up/Open” to “Down/ Close”, or “Down/ Close” to “Up/Open”.


      Inching or continuation move action

      his operation can switch inching/ continuation move mode.


      Lock or open the remote channel

      Lock the channel: Do this operation when you have chosen the channel which you want to lock.

      Open the channel: Do this operation whatever any channel.


      You can delete the limit at any position

      Delete open limit

      Please finish this process within 5 seconds, otherwise it will exit the setting due to overtime.


      Delete close limit

      Please finish this process within 5 seconds, otherwise it will exit the setting due to overtime.


      Delete all limits

      Please finish this process within 5 seconds, otherwise it will exit the setting due to overtime.

      Press the motor’s “Set key”5 times within 5 seconds, then the motor light flashes rapidly, delete limits successfully.


      Yea~ Knowing how the remote control works, it’s even easier to control the curtain motor with a mobile phone App, 2 versions of APP networking have been arranged, so read on!

      App User Manual (ZigBee/ Bluetooth version motor)

      Scan the QR code as below, or search “Smart life” in any App store, to download the App. Then please add the ZigBee or Bluetooth gateway into App first.

      This operation can also be performed when the gateway cannot find the device or the network needs to be reconfigured.

      Method 1: In the case of power on, please press the motor ‘Set key’ 3 times in 5 seconds. The motor will make a sound “Di”, waiting to connect with the App.
      Method 2: Or pressing the remote control ‘Set key’ 6 times, the screen shows 6, then continue to press the ‘Stop key’ once time quickly in less than 5 seconds. The motor will make a sound “Di”, waiting to connect with the App.

      If the configuration fails, please reconnect once.
      (The premise of using method 2 is that the remote control has been connected to the motor.)

      ⚠ Please follow these steps to configure the motor.

      1. Please make sure that the ZigBee or Bluetooth gateway is connected to the App, and then enter the homepage to choose the gateway which you want to connect.
      2. Under the ZigBee page, “Add subdevice”.

      3. The App will now search for the device and register to your account. Choose the curtain motor to connect, then reset the Device Name.

      4. Back to the ZigBee page, choose the motor which you just added.

      5. Enter the motor control page, now you can control the motor by App as well. Enter the motor setting page, can set the motor limit, timing control, change the motor direction, and so on.
      6. On the motor control page, click “∠” in the upper right corner to enter the motor technical parameter setting page, you can check the device information, change the name, and so on.

      Table of Contents

      Related Wiki

      Tell us your needs & expectations

      Just take 1-2 minutes to tell us your ideas and requirements by completing the form below, and you will receive a response from a professional & trusted manufacturer within 12 hours.