Standard Tubular Motor Instruction

Standard Tubular Motor Features

■ Tubular motor is widely applied to roller blinds, awnings, projection screens, garage doors, etc to realize the drive function of automation.
■ Advantage: Mini size, super light, super quiet when working, correct the journey limit, accurate positioning, easily installed
■ It has four parts: Motor, brake, gearbox, and limit switch
■ Overheat protection: When the motor’s surface temperature is over 110℃ after continuously running for about 4-6 minutes, It will stop working for 3-10 minutes, and recover till it cools down.

Standard Tubular Motor Installation

⚠ Announcements before installment

  • Prohibit seepage
  • Prohibit raining
  • Prohibit hitting
  • Prohibit etch
  • Prohibit damaging outer tube
  • Prohibit water

A. Tube Preparation

If it is a round tube, the position of the nails needs to be measured. (Excluding other tube shapes)
Mark the nail position on the tube and plug it into the tail plug
No need to use the nail to fix the tube for the groove tube and octagonal tube

B. Installment of Motor and Tube

① Install crown wheel
② Install driving wheel
③ Install flat output shaft and silent output shaft in snap ring
④ Load in tube
⑤ Hammer in nails without harming motors, installation is finished

C. Install Tube on Bracket

Insert nails into the square side
The effect picture after the installed
Keep horizontal

D. Power Supply and Connection

Description

Hand switch: Up, Stop, Down

“+” Counter-clockwise rotation to increase distance
“-” Clockwise rotation to decrease distance

It cannot be adjusted with an electric screwdriver, must be adjusted with a special adjusting rod. Ensure that the adjustment speed is below 30 RPM per minute.

A. Blue line is the limit position before the adjustment.
B. Red line is the idea limit position after adjustment.

E. Position adjustment

Installment method 1:

a. When the motor limiting head is installed on the left side, the blind is wounded outside.
b. Adjust the up limit button to adjust the up limit.
c. Adjust the down limit button to adjust the down limit.

AB: When the up position limit is higher than the ideal position → Press the “down” button → Clockwise rotation to the “-” direction, until less than the ideal location → Press the ”up“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

BA: When the up position limit is lower than the ideal position → Press the “up” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

BA: When the down position limit is lower than the ideal position → Press the “up” button → Clockwise rotation to the “-” direction, until higher than the ideal location → Press the ”down“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

AB: When the down position limit is higher than the ideal position → Press the “down” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

Installment method 2:

a. When the motor limiting head is installed on the right side, the blind is wounded outside.
b. Adjust the up limit button to adjust the up limit.
c. Adjust the down limit button to adjust the down limit.

AB: When the up position limit is higher than the ideal position → Press the “down” button → Clockwise rotation to the “-” direction, until less than the ideal location → Press the ”up“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

BA: When the up position limit is lower than the ideal position → Press the “up” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

BA: When the down position limit is lower than the ideal position → Press the “up” button → Clockwise rotation to the “-” direction, until higher than the ideal location → Press the ”down“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

AB: When the down position limit is higher than the ideal position → Press the “down” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

Installment method 3:

a. When the motor limiting head is installed in the left direction, the roller blind rolls inward.
b. Adjust the down limit button to adjust the up limit.
c. Adjust the up limit button to adjust the down limit.

AB: When the up position limit is higher than the ideal position → Press the “down” button → Clockwise rotation to the “-” direction, until less than the ideal location → Press the ”up“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

BA: When the up position limit is lower than the ideal position → Press the “up” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

BA: When the down position limit is lower than the ideal position → Press the “up” button → Clockwise rotation to the “-” direction, until higher than the ideal location → Press the ”down“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

AB: When the down position limit is higher than the ideal position → Press the “down” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

Installment method 4:

a. When the motor limit head is installed in the right direction, the roller blind rolls inward.
b. Adjust the down limit button to adjust the up limit.
c. Adjust the up limit button to adjust the down limit.

AB: When the up position limit is higher than the ideal position → Press the “down” button → Clockwise rotation to the “-” direction, until less than the ideal location → Press the ”up“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

BA: When the up position limit is lower than the ideal position → Press the “up” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

B⬅A: When the down position limit is lower than the ideal position → Press the “up” button → Clockwise rotation to the “-” direction, until higher than the ideal location → Press the ”down“ button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

A➡B: When the down position limit is higher than the ideal position → Press the “down” button → Counter-clockwise rotation to the “+” direction, until the ideal location → Setting finished

General Trouble Shooting

ProblemMatterShooting
After installment and plug in electricity motor doesn’t work or works slowlya. The nominal voltage of power and motor are not matched
b. Over loaded
c. Stuck by components for improper installment
a. Change motor with the same voltage as power
b. Change motor with the capacity
c. Examine component
After plug in electricity, motor can only rotate on one directionUp/down position limit remains untapped.Crown wheel to the current operation of the reverse turns to rotation 1-2
When working, motor stops suddenlya. The motor has been on the position of temperature-
precaution, over 130℃
b. Power is off
c. Motor is in the setting terminal point
a. When the temperature drops (after about 3 minutes), the motor will come back to work again
b. Return to normal when electricity comes back;
c. Adjust position limit knob if necessary
According to the controller down button be roller upward run.Wrongly connect wiresExchange the reverse wire and forward wire

Table of Contents

Related Wiki

Tell us your needs & expectations

Just take 1-2 minutes to tell us your ideas and requirements by completing the form below, and you will receive a response from a professional & trusted manufacturer within 12 hours.