CURTAIN MOTOR INSTRUCTIONS (Model: ZM83E-DT)

The following is the instruction manual for ZM83E-DT curtain motor, including the setup instructions for the remote control, the networking instructions of the motor with the App (WiFi, ZigBee, Bluetooth and Bluetooth Mesh versions), as well as the wiring mode (3 wires) and the weak current control (RJ11) of the ZM83E-DT curtain motor, etc.; the following is a detailed introduction for you.

First of all, let’s start with a systematic understanding of the structure of curtain motors and their main functions!

ZM83E-DT Curtain Motor

  • Super silent design
  • Automatic limit setting
  • Power off manual function
  • Wireless control: RF remote, ZigBee, Bluetooth
  • Resistance and stop function
  • Hand light touch-start function
  • Wide voltage power supply
  • Third position limit
  • Fabric rebound journey correction
  • Long service life, durable
  • Resistance then plus pulling function

Button Manual

RJ11: Used for weak current control: Dry contact control, RS485 control, etc. Connect to the data center for controlling center by means of a data line, which is a wired control.


Of course, in addition to the curtain motor, there are remote controls (optional), which have different functions for different models!

Remote Control Instruction


Please feel free to check the curtain ZM83E-DT motor parameters~

Technical Parameters

ModelTorqueRPMRated voltageRated frequency
ZM83E-DT1.2N.m100RPM100-240VAC50/60HZ
Max currentMax powerRunning speedReceive frequencyReceive sensitivity
0.25A55W0.15m/s433.92Mhz-110dBM

Okay, now let’s look at the curtain motor’s wiring mode and the weak control switch connection operating manual.

Wiring Mode

Weak current control switch connection

Operation Manual

  1. If press “Open/ Close/ Stop Switch”, the curtain Open/ Close turn; If press “Open/ Close/ Stop Switch” again, the curtain stop.
  2. If press “Close/ Open/ Stop Switch”, the curtain Close/ Open turn; If press “Close/ Open/ Stop Switch” again, the curtain stop.

Operation Manual

  1. If press “Open/ Close/ Stop Switch”, the curtain Open/ Close turn; If press “Open/ Close/ Stop Switch” again, the curtain stop.
  2. If press “Close/ Open/ Stop Switch”, the curtain Close/ Open turn; If press “Close/ Open/ Stop Switch” again, the curtain stop.
  3. If press “Stop Switch”, then the curtain stop.


After a general understanding of ZM83E-DT curtain motors, you should be eager to know how to control them, right? Here’s how to control the curtain motor by remote control.

Remote Control and Network Setting Manual

These operations only work for the remote control within the effective control distance, and the motor is in the power-on state, otherwise it doesn’t work.



Automatically set limit

  1. Control the curtain to open, it will automatically stop when it goes to the fully open state, and the automatic setting of the open limit is completed. (Figure A)
  2. Control the curtain to close, it will automatically stop when it goes to the fully closed state, and the automatic setting of the close limit is completed. (Figure B)

If the travel limit position is wrong, please click the motor’s ‘Set key’ 5 times within 5 seconds to delete the limit, and reset it.

Delete the remote current channel from the motor


Delete current remote from the motor

To cancel the connection between the motor and current remote all channels.


Delete all remote control from the motor



The following functions can be set as personal needs.

Change the remote control direction

When the control direction is opposite, the remote control can be used to switch the direction, and you can repeat the operation to switch.


Inching or continuation move action

When the inching action is needed, perform the following operations. (Repeat this operation can switch back to the continuation move mode.)


Lock or open the remote channel

If you need to hide the extra channels, you can perform the following operations. (Repeat the operation to unlock channel.)

Lock the channel: Do this operation when you have chosen the channel which you want to lock.
Open the channel: Do this operation whatever any channel.
(Repeat this operation for lock or open the channel.)


You can delete the limit at any position

Method 1: Remote control deletes position limit


Method 2: Motor’s ‘Set key’ deletes position limit

Press the motor’s ‘Set key’ 5 times in less than 5 seconds; At last, the motor light flashes out, set successfully.


Yea~ Knowing how the remote control works, it’s even easier to control the curtain motor with a mobile phone App, 4 versions of APP networking have been arranged, so read on!

Smart Life App User Manual (WiFi version motor)

Scan the QR code as below, or search “Smart life” in any App store, to download the App.

Method 1: In the case of power on, please press the motor ‘Set key’ 3 times in 5 seconds. The indicator light flashes quickly and then goes out, waiting to connect with the App.
Method 2: Or pressing the remote control ‘Set key’ 6 times, the screen shows 6, then continue to press the ‘Stop key’ once time quickly in less than 5 seconds. The indicator light flashes quickly and then goes out, waiting to connect with the App.

If the configuration fails, please reconnect once.
(The premise of using method 2 is that the remote control has been connected to the motor.)

Click ‘+’ in the upper right corner to enter the add device page and select Add Manually, or automatically discover and add.

Note:
The App supports two configurations: EZ mode, and AP mode.
EZ mode: The default mode is fast-speed connected internet mode.
Use AP mode when there is no WiFi. It adopts a hot distribution network.

App percentage control: composed of 10 percentage control positions such as 0, 10, 20, 30 …90, 100.

  • Lights flash quickly: Configuring network.
  • Lights flash slowly: AP Mode Configuring.
  • Lights turn on and keep: Has connected to the router and cloud.
  • Lights turn off: After the light turns on for 3 seconds, the light turns off and the WiFi configuration is successful.

Note: Please make sure your phone and smart device are connected in the same WiFi.


App User Manual (ZigBee/ Bluetooth version motor)

Scan the QR code as below, or search “Smart life” in any App store, to download the App. Then please add the ZigBee or Bluetooth gateway into App first.

This operation can also be performed when the gateway cannot find the device or the network needs to be reconfigured.

Method 1: In the case of power on, please press the motor ‘Set key’ 3 times in 5 seconds. The indicator light flashes quickly and then goes out, waiting to connect with the App.
Method 2: Or pressing the remote control ‘Set key’ 6 times, the screen shows 6, then continue to press the ‘Stop key’ once time quickly in less than 5 seconds. The indicator light flashes quickly and then goes out, waiting to connect with the App.

If the configuration fails, please reconnect once.
(The premise of using method 2 is that the remote control has been connected to the motor.)

⚠ Please follow these steps to configure the motor.

1. Please make sure that the ZigBee or Bluetooth gateway is connected to the App, and then enter the homepage to choose the gateway which you want to connect.
2. Under the ZigBee page, “Add subdevice”.

3. The App will now search for the device and register to your account. Choose the curtain motor to connect, then reset the Device Name.

4. Back to the ZigBee page, choose the motor which you just added.

5. Enter the motor control page, now you can control the motor by App as well. Enter the motor setting page, can set the motor limit, timing control, change the motor direction, and so on.
6. On the motor control page, click “∠” in the upper right corner to enter the motor technical parameter setting page, you can check the device information, change the name, and so on.


App User Manual (Bluetooth Mesh version motor)

Scan the QR code as below, or search “Smart life” in any App store, to download the App. Then please add the ZigBee or Bluetooth gateway into App first.

This operation can also be performed when the gateway cannot find the device or the network needs to be reconfigured.

Method 1: In the case of power on, please press the motor ‘Set key’ 3 times in 5 seconds. The indicator light flashes quickly and then goes out, waiting to connect with the App.

Method 2: Or pressing the remote control ‘Set key’ 6 times, the screen shows 6, then continue to press the ‘Stop key’ once time quickly in less than 5 seconds. The indicator light flashes quickly and then goes out, waiting to connect with the App.

If the configuration fails, please reconnect once.
(The premise of using method 2 is that the remote control has been connected to the motor.)

⚠ Please follow these steps to configure the motor.

1. Pease turn on the Bluetooth of your mobile phone first, and then enter the App after the main interface will automatically pop up a new device, click “Add”.

2. Enter the Add Device interface, click “+” to add the motor, then reset the device name, after the addition is successful, click “Done”.
3. Enter the motor control page, now you can control the motor by App as well. Enter the motor setting page, can change the motor direction, and so on.
4. On the motor control page, click “∠” in the upper right corner to enter the motor technical parameter setting page,you can check the device information, change the name, and so on.
.

Table of Contents

Related Wiki

Tell us your needs & expectations

Just take 1-2 minutes to tell us your ideas and requirements by completing the form below, and you will receive a response from a professional & trusted manufacturer within 12 hours.